Limestone Slabs
Limestone Slabs
Limestone is the quiet stone. It reads as a solid colour from three metres away and only shows its shell fragments and fine bedding lines when you get close — which is exactly why architects keep specifying it for walls that should not compete with anything. It is also softer and more absorbent than granite or quartzite, so the finish and the sealer are not decoration, they are what keeps the surface serviceable. We cut and finish it in Shuitou and ship sealed.
Browse by use
| What the slab becomes | What to specify | Link |
|---|---|---|
| Interior wall cladding, large flat planes | 2cm, honed, full-support substrate — limestone will not span a void | /products/interior-stone |
| Vanity tops and bathroom surfaces | Honed rather than polished; wet areas need a penetrating sealer, not a film | /products/countertops/vanity-tops-and-bath-tops |
| Kitchen worktops in a low-acid household | Honed resists kitchen acids better than polished marble; still seal it | /products/countertops |
| Fireplace surrounds and hearths | 3cm where the edge is exposed; confirm the substrate is non-combustible | /products/interior-stone/fireplace-hearth-and-surrounds |
| Exterior wall in a mild, non-freezing climate | Brushed or leathered for grip; do not use it where it freezes | /products/outdoor-stone/exterior-wall-claddings |
| Floor tiles in a hallway or bathroom | 2cm with a honed face; expect to re-seal every few years | /products/interior-stone/floor-tiles-and-wall-tiles |
Why limestone needs a finish decision before a thickness decision
The same block behaves like two different stones depending on how it leaves the line. Polished closes the pores and deepens the colour, and it shows every scuff. Honed keeps the tone flat and hides wear, which is why it is the default for walls and vanities. Brushed and leathered open the surface slightly and give grip underfoot, and they are the only sensible choice outdoors or on a floor that gets wet.
Absorption is the number that decides where it can go. Portuguese grey tests around 0.3% on a sealed, honed face and higher on a raw brushed face — either way it is porous by granite standards, and a wet area without a penetrating sealer will show tide marks within a season. We seal at the factory and tell you what to re-apply, rather than letting you find out from a stain.
And it is soft. Around 120 MPa compressive strength and a Mohs hardness well below granite means it cuts easily, profiles cleanly, and also chips at an arris if the edge is left sharp. On worktops we put a small chamfer or a bullnose on every exposed edge as standard, because a square limestone edge is a maintenance item.
FAQ
Is limestone suitable for a kitchen worktop?
Yes, with conditions. Honed limestone resists mild acids better than polished marble, and it does not show etching the way calcite-rich marble does. It still stains if oil sits on it, so it needs a penetrating sealer and a wipe-down habit. If the kitchen is heavily used we usually quote granite or quartzite instead and say why.
What is the difference between honed, brushed and leathered?
Honed is a smooth matte surface, flat and even. Brushed is mechanically abraded to a slightly open, textured face with a softer look. Leathered follows the natural bedding and gives the most grip and the most visible texture. Honed for walls and vanities, brushed or leathered for floors and exteriors.
Can limestone be used outside?
In a mild climate without hard frost, yes — brushed or leathered, on a drained substrate. In a freeze-thaw climate, no. Water sits in the pores, freezes, and spalls the face, and no sealer stops that permanently. We will tell you before you order rather than after.
What thicknesses do you supply?
2cm (3/4 inch) for wall cladding, vanity tops and worktops on cabinetry. 3cm (1-1/4 inch) for floors, exposed edges, hearths and anywhere the slab carries load. Larger sections such as fireplace surrounds are cut to the drawing rather than stocked.
Does it need sealing, and how often?
Yes, and we seal it before packing so it arrives protected. On a vanity or a kitchen surface, expect to re-apply a penetrating sealer every one to three years depending on use. On a wall it can go much longer. We send the product type we used so you are not guessing.
Can you match the fossil pattern across several slabs?
Yes, if you order them together. Fossil-bed limestone has a directional pattern, and consecutive slices from one block will bookmatch. Slabs from a different block will be the same colour and a different drawing. Order every slab for the room at once.
Send the area, the application and the finish you want, and we come back with photographs of the slabs on the rack, the sealed absorption figures for that finish, and a price per square metre with packing and export documentation included.
Request a Quote